Vad betyder det när den lilla röda lampan blinkar? Den vid sista skott spärren.
Mvh
Röd lampa blinkar?
Re: Röd lampa blinkar?
15 sekunder med Google.
http://www.airsoftohio.com/forums/showt ... hp?t=26247
~FIRING / FAILURE~
A) PTW doesn't cycle - Troubleshoot!
- Open PTW receiver and examine LED on PCB just forward of the optical sensors for the sector gear.
- Place selector lever in SAFE mode - Then Turn selector to SEMI
- IF LED on PCB flashes once then system is active and getting power from battery.
- Pull trigger once. IF LED begins to flash cotinously then there are three major failure areas to examine. First, examine the gearbox and ensure there is no debris in the gears preventing rotation. Second, examine the motor(remove motor plate and grip) and ensure there are ample brush material and the wires are secured to the motor contacts. Third, Ensure the fuse and mosfet system in the stock is not grounding to the stock tube and the fuse is not destroyed.
- If all of these areas check out then it's most likely the battery that is low on charge and needs to be replaced.
B) PTW fires but no BBs load
- Magazine is empty but has not tripped the STOP FIRE mode.
- Magazine has BB stoppage and cannot load BBs to HOP.
- BB is jammed in barrel (listen for sucking sound when PTW cycles).
C) PTW partial cycles or fails to cycle completely
- Ensure battery is adaquetly charged.
- Ensure there is brush material left on the motor brushes.
- Ensure the wires are firmly connected to the motor.
- Ensure there is no debris blocking the gears within the gearbox.
D) PTW cycles either partially(semi), or too many revolutions(Burst/Auto)
- Grease or debris has coated the optical sensors. This must be cleaned compeltely.
- Grease or debris has covered or filled the pass through holes on the Sector cam gear rack. These must be cleaned and freed of debris or grease.
- MOSFET controller is experiencing failure, this part needs replacement.(this is RARE and not expected in 99% of the cases)
- Motor brushes are nearing 90% useage and need replacing. Replace motor brushes with new 30% silver content systema brushes for better performance.
http://www.airsoftohio.com/forums/showt ... hp?t=26247
~FIRING / FAILURE~
A) PTW doesn't cycle - Troubleshoot!
- Open PTW receiver and examine LED on PCB just forward of the optical sensors for the sector gear.
- Place selector lever in SAFE mode - Then Turn selector to SEMI
- IF LED on PCB flashes once then system is active and getting power from battery.
- Pull trigger once. IF LED begins to flash cotinously then there are three major failure areas to examine. First, examine the gearbox and ensure there is no debris in the gears preventing rotation. Second, examine the motor(remove motor plate and grip) and ensure there are ample brush material and the wires are secured to the motor contacts. Third, Ensure the fuse and mosfet system in the stock is not grounding to the stock tube and the fuse is not destroyed.
- If all of these areas check out then it's most likely the battery that is low on charge and needs to be replaced.
B) PTW fires but no BBs load
- Magazine is empty but has not tripped the STOP FIRE mode.
- Magazine has BB stoppage and cannot load BBs to HOP.
- BB is jammed in barrel (listen for sucking sound when PTW cycles).
C) PTW partial cycles or fails to cycle completely
- Ensure battery is adaquetly charged.
- Ensure there is brush material left on the motor brushes.
- Ensure the wires are firmly connected to the motor.
- Ensure there is no debris blocking the gears within the gearbox.
D) PTW cycles either partially(semi), or too many revolutions(Burst/Auto)
- Grease or debris has coated the optical sensors. This must be cleaned compeltely.
- Grease or debris has covered or filled the pass through holes on the Sector cam gear rack. These must be cleaned and freed of debris or grease.
- MOSFET controller is experiencing failure, this part needs replacement.(this is RARE and not expected in 99% of the cases)
- Motor brushes are nearing 90% useage and need replacing. Replace motor brushes with new 30% silver content systema brushes for better performance.
Re: Röd lampa blinkar?
Tusen tack kära du